1.8方小型混凝土攪拌機以其小巧可靈敏挪動的特性為很多人所知,那么小型混凝土攪拌機怎樣運用呢,我們就來引見一下小型混凝土攪拌機如何運用?
1.8 square small concrete mixer with its small and sensitive to move characteristics for a lot of people know, so how to use small concrete mixer, we will introduce how to use small concrete mixer?
:選擇平整堅實的場地,四周有良好的排水溝渠,將1.8方小型混凝土攪拌機推場地,等候備用。
First: choose a flat and solid site, surrounded by good drainage ditch, push 1.8 square meters of small concrete mixer to the site, waiting for standby.
第二:檢查混凝土攪拌機的軸承、電動機和電器元件的接線結實,維護接零或接地電阻能否契合規則,如有異常需求立刻改換。
Second: check the concrete mixer bearing, motor and electrical components of the wiring firm, maintenance zero or grounding resistance can fit the rules, if there is abnormal demand immediately change.
第三:接上混凝土攪拌機的電源,按下啟動按鈕,使混凝土攪拌機空載運轉,檢查攪拌桶或葉片旋轉方向與筒體上箭頭的方向能否分歧。
Third: connect to the power supply of the concrete mixer, press the start button to make the concrete mixer run without load, check the direction of rotation of the mixing barrel or blade and the direction of the arrow on the barrel can be divided.
第四:攪拌機啟動后,應使攪拌筒到達正常轉速后停止上料,上料時及時加水。加料的次序為石子--水泥--沙子或者沙子--水泥--石子。
Fourth: after the mixer is started, the mixing cylinder should stop feeding after reaching the normal speed, and water should be added in time when feeding. The order of feeding is stone - cement - sand or sand - cement - stone.
第五:1.8方小型混凝土攪拌機處在攪拌的工作中時,留意察看機械的運轉狀況,當有異?;蜉S承溫升過高等現象時,應停機檢查。
Fifth: 1.8 square small concrete mixer in the work of mixing, pay attention to the operation of the machinery, when there is abnormal or bearing temperature rise too high phenomenon, should stop inspection.
第六:完成一次攪拌工作后,將攪拌筒內的攪拌物全部倒出后,方可參加新的攪拌物。
Sixth: after the completion of a mixing work, will be in the mixing cylinder all the mixing out, can participate in the new mixing.
第七:運用過后要及時潔凈,以免剩余的攪拌物吸附在攪拌筒壁上,1.8方
混凝土攪拌機采用底盤發起機取力方式。安裝的作用是經過全功率驅動器將發起機動力取出,經液壓系統驅動攪拌筒,攪拌筒在進料和運輸過程中正向旋轉,以利于進料和對混凝土停止攪拌,在出料時反向旋轉,在工作終結后切斷與發起機的動力聯接。
Seventh: after use to timely clean, so as to avoid the remaining mixing material adsorption on the mixing cylinder wall, 1.8 square concrete mixer adopts chassis starter to take force. The function of installation is to take out the power of the starter through the full power driver, and drive the mixing cylinder through the hydraulic system. The mixing cylinder is rotating in the process of feeding and transportation, so as to facilitate the feeding and stop mixing of concrete, reverse rotation when discharging, and cut off the power connection with the starter after the end of work.