混凝土攪拌機在攪拌任務中發揮著重要的作用，所以大部分時間它都是在工作中，所以日子一長，就會對設備產生很大的耗損，因此會時常出現各種各樣的問題，比如說攪拌機水溫升高，這可不算是一個好現象，下面我們來講講出現原因吧。

　　Concrete mixer in stir mission plays an important role, so most of the time it is at work, so the day a long, will produce very big loss to the equipment, so often appear all sorts of problems, such as mixer temperature rise, this is not a good sign, we talk about the reason below.

　　燃燒啟動自動加料攪拌的操作流程不正確；自動加料攪拌水箱堵塞，外部堵塞應用水或氣體；內部堵塞會影響冷卻液的循環，同時會產生壓力。這時候會有兩種影響，一是水箱漏水，二是高速行駛時水溫特別高；氣缸損壞，燃燒室和水道被沖洗。此時，排水管會放水或冒白煙，導致水箱經常缺水；水道和油道沖洗干凈（油有水呈白色）；水道與水道沖刷，形成缸體散熱不良，特別是在高速運轉時；散熱風扇不轉，散熱風扇可由溫控開關控制；它也可以由水溫傳感器控制。

　　The operation process of automatic feeding and stirring at combustion start is not correct; Automatic feeding mixing tank blockage, external blockage should be removed by water or gas; Internal blockage can interfere with coolant circulation and create pressure. At this time there will be two kinds of influence, one is the water tank leakage, the other is the water temperature is very high when driving at high speed; Cylinder damaged, combustion chamber and channel flushed. At this point, the drain will release water or smoke white, resulting in water tank often water; Water channel and oil channel wash clean (oil with water is white); Channel and channel erosion, the formation of poor heat dissipation cylinder, especially in high-speed operation; The heat dissipation fan does not work. The heat dissipation fan can be controlled by the temperature control switch. It can also be controlled by water temperature sensors.

　　另外，在使用混凝土攪拌機前，先用少量砂漿沖洗空腔，然后將砂漿刮掉，否則粘附在筒壁上的水泥砂漿會慢慢流失；然后根據實際需要稱量不同的混凝土。原料，然后依次加入石子、沙子、水泥到混凝土攪拌機中；緩慢啟動攪拌機，在攪拌過程中緩慢均勻地加水，將物料攪拌均勻。加料時間控制在兩分鐘以內；攪拌兩分鐘左右，將混合物倒在鐵板上，然后用手攪拌大約一到兩分鐘，確?；旌衔锍浞謹嚢?；關閉電源并清潔儀器。

　　In addition, before using the concrete mixer, rinse the cavity with a small amount of mortar and then scrape off the mortar, otherwise the cement mortar adhered to the wall of the cylinder will be slowly lost; Then weigh the different concrete according to actual needs. Raw materials, and then add stones, sand, cement to the concrete mixer; Start the mixer slowly, add water slowly and evenly during the mixing process, and mix the material evenly. Feeding time is controlled within two minutes; Stir for about two minutes, pour the mixture onto the tin plate, then stir by hand for about a minute or two, making sure the mixture is well stirred; Turn off the power and clean the instrument.

　　因此，如果操作人員不想讓自己的混凝土攪拌機時常出現問題的話，就需要在使用前后進行基本的保養以及檢查工作，清潔工作也是重中之重，不可大意！更多相關內容的了解就來網站www.gdfcx.net看看吧。

　　Therefore, if the operator does not want to let their concrete mixer often problems, you need to use before and after the basic maintenance and inspection work, cleaning work is also a top priority, not careless! For more information, visit www.gdfcx.net.