如今可以看到建筑工地上天天在施工，攪拌車就不能停，高溫天氣對自動攪拌車來說也是一個嚴峻的考驗，尤其是發動機高溫故障，今天就給大家介紹一下發動機高溫故障的辦法。

　　Now we can see that the construction site is under construction every day, and the mixer can not stop. The high temperature weather is also a severe test for the automatic mixer, especially the engine high temperature fault. Today, I will introduce the solution to the engine high temperature fault.

　　發動機高溫，但是冷卻液沒有減少，就是說自動攪拌車發動機過熱，但是冷卻系統工作正常，這時應保持發動機怠速運轉，嚴禁熄火，用冷水澆散熱器表面加速降溫，在溫度下降到50度左右的時候，用濕毛巾旋開水箱蓋，進行降溫，要檢查油尺刻度是否在正常范圍內。

　　Engine temperature, not reduce, but the coolant is automatic mixing car engine overheating, but the cooling system work is normal, should maintain the engine idle speed running at this moment, it is forbidden to stall, with cold water poured accelerated cooling radiator surface, when the temperature drops to 50 degrees, use a wet towel to unscrew the tank cover, cooling, to check whether the oil dipstick scale is within the normal range.

　　發動機水溫過高，冷卻系統循環出現故障的原因有很多，比如節溫器，冷卻硅油風扇，風扇皮帶等損壞導致冷卻系統無法正常工作。要保持發動機怠速狀態，用冷水給散熱器降溫。

　　There are many reasons for the failure of engine water temperature and cooling system circulation. For example, the cooling system cannot work normally due to the damage of thermostat, cooling silicone oil fan and fan belt. To keep the engine idle, cool the radiator with cold water.

　　在發動機溫度降到80度以下時，采取間斷熄火，踩下熄火開關或者拔掉電噴系統傳感器，用起動機帶動發動機運轉，10-15秒為一個運轉周期，運轉降溫，檢查機油尺刻度是否在正常范圍內。

　　When the engine temperature falls below 80 degrees, take intermittent flameout, step on the flameout switch or unplug the sensor of the efI system, drive the engine with the starter, 10-15 seconds as a cycle, the operation of cooling, check whether the oil ruler scale is in the normal range.

　　自動攪拌車發動機在沒有冷卻液狀態下運轉，尤其是在夏天，是會造成嚴重事故的，這時采用任何冷卻水澆散熱器的方式降溫都是無效的，發動機運轉也無法散熱。此時在發動機怠速狀態下，打開機油加注口，迅速加注潤滑油，這主要是因為在徹底缺水狀態下，發動機潤滑油會隨之大量高溫蒸發，須迅速補充。

　　When the engine runs without coolant, especially in summer, it will cause serious accidents. At this time, any cooling water pouring on the radiator is ineffective, and the engine cannot dissipate heat. At this time, in the engine idle state, open the oil filling port, quickly add lubricating oil, this is mainly because in the complete water shortage, the engine lubricating oil will then evaporate at high temperature, must be quickly supplemented.

　　自動攪拌車發動機高溫故障的辦法就到這里，需要去多多進行了解，這樣在出現問題時才能冷靜處理。更多內容的了解您可以來網站www.gdfcx.net看看。

　　The solution to the high temperature failure of the engine of the automatic stirring vehicle is here. It is necessary to understand more, so that when there is a problem, we can deal with it calmly. For more information, you can visit www.gdfcx.net.