概述:混凝土攪拌機正常工作的基礎要求是什么呢?如欲使混凝土攪拌機正常工作、延長使用壽命,務請遵守下列各款:
What are the basic requir
混凝土攪拌機正常工作的基礎要求是什么呢?如欲使混凝土攪拌機正常工作、延長使用壽命,務請遵守下列各款:
What are the basic requirements for normal operation of concrete mixer? If you want to make the concrete mixer work normally and prolong its service life, please comply with the following clauses:
(1)在駕駛室內操縱操作手柄時,請勿踩踏加速踏板。
(1) When operating the operating handle in the cab, do not step on the accelerator pedal.
(2)攪拌機行駛時,操作手柄應置于“攪動”檔內,駕駛室內的防逆手柄亦應加以鎖定。如操作手柄仍置于“進料、攪拌”檔內,則會降低預拌混凝土的質量,影響攪拌機的行駛性能。
(2) When the mixer is running, the operating handle shall be placed in the "stirring" gear, and the anti reverse handle in the cab shall also be locked. If the operating handle is still in the "feeding and mixing" position, the quality of the ready mixed concrete will be reduced and the driving performance of the mixer will be affected.
(3)攪拌機開始工作前,發動機應空轉預熱。
(3) Before the mixer starts working, the engine shall be idled and preheated.
(4)扳動操作手柄時,切勿用力過猛。
(4) Do not pull the operating handle too hard.
車輛行駛前,應做好下列準備工作:
Before driving, the following preparations shall be made:
(1)將操作手柄扳“攪動”位置,使拌筒以攪動速度回轉。
(1) Turn the operating handle to the "stirring" position to rotate the mixing drum at the stirring speed.
(2)將駕駛室內推拉軟軸操作手柄卡在定位塊的槽中鎖定。
(2) Lock the push-pull flexible shaft operating handle in the cab in the groove of the positioning block.
(3)檢查卸料槽鎖柄是否扣牢。
(3) Check whether the lock handle of the discharge chute is fastened.
供水系統使用操作:
Operation of water supply system:
開啟供水裝置的氣壓開關;
Turn on the air pressure switch of the water supply device;
用水槍沖洗時,請開啟閥門④;
When flushing with water gun, please open valve ④;
沖洗進料斗、出料斗、葉片時,請開啟閥門②、③;
When flushing the feed hopper, discharge hopper and blade, please open valves ② and ③;
加水或排水時請開閥門①;
Please open valve ① when adding water or draining water;
關閉供水裝置的進氣開關,打開排氣閥,使水箱與大氣相通,即可向水箱內加水。使用壓力水箱中的水沖洗時,先關閉排氣閥,再打開氣源進氣閥門即可(詳見產品上操作說明)。
Close the air inlet switch of the water supply device and open the exhaust valve to connect the water tank with the atmosphere, and then add water to the water tank. When flushing with water in the pressure water tank, close the exhaust valve first and then open the air inlet valve of the air source (see the operating instructions on the product for details).
When the vehicle is stopped in winter, please drain all the remaining water in the water tank, pipeline and water gun to avoid freezing the parts of the water supply system and causing unnecessary losses. For more information about blenders, please visit our website http://www.gdfcx.net Consult and understand.