小型攪拌機設備在長時間的使用中難免會存在一定的故障問題，為了避免設備在使用中的良好性能，就需要我們對設備進行合理的維修才行。那么設備在維修過程中存在哪些需要注意的事項呢？

It is inevitable that there will be some failures in the small mixer equipment in the long use. In order to avoid the good performance of the equipment in use, we need to carry out reasonable maintenance on the equipment. What should be paid attention to during equipment maintenance?

攪拌筒：在初次使用到50小時時，要及時檢查罐體及其他部位螺栓是否有松動，每天行車前要檢查托輪與滾道的潤滑，每個月打開一次托輪護罩，清理內部的油污并添加潤滑油脂。

Mixing drum: when the tank and other parts are used for 50 hours for the first time, timely check whether the bolts of the tank and other parts are loose. Before driving every day, check the lubrication of the supporting wheel and the raceway. Open the supporting wheel shield once a month, clean the internal oil stain and add lubricating grease.

液壓驅動系統：液壓系統是攪拌車的核心系統。為保證攪拌車能正常工作，攪拌罐能運轉正常，須在每次車輛發動前檢查油路散熱器和減速機的液壓油位，保證油位指示在視窗范圍內。同時要保證它的清潔，不能讓灰塵等污染系統液壓油，造成系統不能正常工作或損壞。

Hydraulic drive system: the hydraulic system is the core system of the mixer. In order to ensure that the mixer truck can work normally and the mixing tank can operate normally, the hydraulic oil level of the oil radiator and reducer must be checked each time before the vehicle is started to ensure that the oil level indication is within the scope of the window. At the same time, ensure that it is clean, and do not allow dust and other pollutants to pollute the hydraulic oil of the system, causing the system to not work normally or be damaged.

供水系統：氣壓供水系統加水量好在水箱的四分之三處，經常檢查閥體是否堵塞或是否有工作異常。在有結冰可能的環境中使用時，供水系統須排空存水，防止管路凍裂。

Water supply system: air pressure water supply system can add water at three quarters of the water tank. Check the valve body frequently for blockage or abnormal operation. When the water supply system is used in an environment with the possibility of icing, the water storage must be drained to prevent the pipeline from freezing.

還有一點不能用水直接沖洗小型攪拌機車身，攪拌罐車身內部機構是比較復雜的，凹槽、通孔設計比較多，一旦用水沖洗了，那么水分沉積在機身內不容易干燥，就容易使得零部件銹蝕。

Another point is that the body of a small mixer cannot be washed directly with water. The internal mechanism of the body of the mixing tank is relatively complex, and there are many grooves and through-hole designs. Once washed with water, the water deposited in the body is not easy to dry, and the parts are easy to rust.

小型攪拌機在維修中需要注意的事項就講解到這里了，您對此有什么問題就來我們網站http://www.gdfcx.net咨詢了解吧！

Here are the matters needing attention in the maintenance of the small mixer. If you have any problems, please come to our website http://www.gdfcx.net Ask and understand!