概述:使用混凝土攪拌機時要注意保養,及時清理,避免出現各種原因耽誤生產。中科聚峰混凝土攪拌機是研發、制造、銷售為一體的工程機械制造企業,不論是混凝土攪拌站設備還是混凝土攪拌機設
使用混凝土攪拌機時要注意保養,及時清理,避免出現各種原因耽誤生產。中科聚峰混凝土攪拌機是研發、制造、銷售為一體的工程機械制造企業,不論是混凝土攪拌站設備還是混凝土攪拌機設備都深受用戶的好評,是一家值得信賴的廠家。歡迎廣大客戶前來咨詢訂購或到廠考察。。
When using the concrete mixer, pay attention to maintenance and timely cleaning to avoid delaying production for various reasons. Zhongke Jufeng concrete mixer is a construction machinery manufacturing enterprise integrating R & D, manufacturing and sales. Both concrete mixing plant equipment and concrete mixer equipment are highly praised by users. It is a reliable manufacturer. Welcome customers to consult and order or visit our factory..
混凝土攪拌機是生產混凝土的主要設備,混凝土攪拌機是把水泥、砂石骨料和水混合并拌制成混凝土混合料的機械。在使用過程中要注意日常保養,如果不注意保養,可能會出現抱軸的情況,混凝土攪拌機出現抱軸的原因也是有多種的。
Concrete mixer is the main equipment for producing concrete. Concrete mixer is a machine that mixes cement, gravel aggregate and water into concrete mixture. Pay attention to daily maintenance during use. If you don't pay attention to maintenance, axle holding may occur. There are many reasons for axle holding of concrete mixer.
1、可能是原料投料位置問題。攪拌混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水喝外加劑等。原料水泥若包裹砂石遇水結塊,如果攪拌不充分就容易粘在攪拌軸上,若水泥進料口位置方向不合理,使攪拌軸不能快速充分攪拌,就容易形成抱軸現象。
1. It may be the feeding position of raw materials. The materials used for mixing concrete are mainly sand and gravel aggregate, cement, fly ash, water and drinking admixture, etc. If the wrapped sand and gravel of the raw cement agglomerates with water, it is easy to stick to the mixing shaft if it is not fully stirred. If the position and direction of the cement feed inlet is unreasonable, the mixing shaft cannot be quickly and fully stirred, and it is easy to form the phenomenon of shaft holding.
2、混凝土攪拌機進水管與沖水位置原因。沖水點位置和沖洗方向不正確的話,又或者是沖水壓力過低,導致水在進入主機內部后,不能將暫時粘結在軸上的混凝土沖洗掉,則時間久了就容易形成抱軸。
2. Causes of water inlet pipe and flushing position of concrete mixer. If the position and direction of the flushing point are incorrect, or the flushing pressure is too low, so that the water cannot flush the concrete temporarily bonded to the shaft after entering the main engine, it is easy to form the shaft holding after a long time.
3、在結構生產之后沒有及時對混凝土攪拌機內部進行清洗,或清洗的不干凈,導致攪拌軸表面仍有殘留的混凝土,干燥后凝固在攪拌軸上,如果長期如此則非常容易產生抱軸現象。
3. After the production of the structure, the interior of the concrete mixer is not cleaned in time, or the cleaning is not clean, resulting in residual concrete on the surface of the mixing shaft, which is solidified on the mixing shaft after drying. If this is the case for a long time, it is very easy to produce shaft holding phenomenon.