攪拌機是一種工作強度大，可靠性要求高的工程機械，要保證其的工作狀態，日常保養尤為重要。那么下面就來講講小型攪拌機新車購入養護需知吧。

Mixer is a kind of construction machinery with high working intensity and high reliability requirements. To ensure its efficient working state, daily maintenance is particularly important. Now let's talk about the need to know about the purchase and maintenance of new small blenders.

對于新購入的小型攪拌機，初次使用50小時左右，即應檢查各處螺栓緊固情況，包括罐體封頭與減速機的連接螺栓，減速機底座與前臺的連接螺栓，拖輪底座與機架的連接螺栓，以及副梁與大梁的連接螺栓等，以后要保證每月定期檢查一次。每天行車前檢查托輪與滾道的結合面潤滑油是否干澀，應及時補充，保持良好的潤滑效果。

For the newly purchased small mixer, after the initial use of about 50 hours, it is necessary to check the fastening of bolts everywhere, including the connecting bolts between the tank head and the reducer, the connecting bolts between the reducer base and the front desk, the connecting bolts between the tugboat base and the frame, and the connecting bolts between the auxiliary beam and the girder. In the future, it is necessary to ensure that the bolts are checked regularly once a month. Before driving every day, check whether the lubricating oil on the joint surface of the supporting wheel and the raceway is dry, and supplement it in time to maintain good lubrication effect.

每次在車輛發動之前，檢查冷卻器和減速機的油位，保證油位指示在目視范圍內；檢查液壓油路的密封情況，保持液壓系統清潔和密封，以免塵粒和水份等污染系統液壓油，造成系統不能正常工作或損壞。經常性檢查管路及液壓設備的緊固螺栓是否有松動，保障設備的，要時更換螺栓。

Before starting the vehicle every time, check the oil level of the cooler and reducer to ensure that the oil level indication is within the visual range; Check the sealing condition of the hydraulic oil circuit, and keep the hydraulic system clean and sealed, so as to prevent dust particles and water from polluting the hydraulic oil of the system, causing the system to fail to work normally or damage. Regularly check whether the fastening bolts of pipelines and hydraulic equipment are loose to ensure the safety of the equipment, and replace the bolts when necessary.

經常檢查散熱器的風扇和溫控開關的性能，保證其正常工作,油溫一般在65℃左右，風扇會自動打開。注意觀察散熱器上的壓力表指示，當指針位于紅色區域時，應更換濾芯，對于使用一年以上的濾芯，即使指針不在紅色區域，也應該及時更換。

Regularly check the performance of the fan and temperature control switch of the radiator to ensure their normal operation. The oil temperature is generally about 65 ℃, and the fan will turn on automatically. Pay attention to the indication of the pressure gauge on the radiator. When the pointer is in the red area, the filter element should be replaced. For the filter element that has been used for more than one year, even if the pointer is not in the red area, it should be replaced in time.

少每月一次清理小型攪拌機托輪和滾道上的污物；通過托輪上的油嘴，向托輪內注入潤滑油脂。保證傳動軸少每月潤滑一次。

Clean the dirt on the supporting wheel and roller track of the small mixer at least once a month; Inject lubricating grease into the supporting roller through the nozzle on the supporting roller. Ensure that the transmission shaft is lubricated at least once a month.

液壓系統部件精度較高，保養簡易，但要求很高，液壓油要定期更換，運行500小時，以后2000小時或少每年更換一次，濾芯應該同時更換。加油或換油時，發動機須處于停止狀態，否則將造成液壓系統損壞。

The components of the hydraulic system have high accuracy and easy maintenance, but the requirements are very high. The hydraulic oil should be replaced regularly. It should be operated for 500 hours for the first time, and then replaced for 2000 hours or at least once a year. The filter element should be replaced at the same time. When refueling or changing oil, the engine must be stopped, otherwise the hydraulic system will be damaged.

換油后，須檢查液壓系統的密封性能，并重新緊固所有的螺栓，要時更換新的密封元件。禁止使用不合格油品或不同牌號的液壓油混用。在新換好油品后，讓發動機在攪拌筒不轉的情況下，空轉15分鐘，檢查油位是否合適。

After oil change, check the sealing performance of the hydraulic system, retighten all bolts, and replace new sealing elements when necessary. It is absolutely forbidden to use unqualified oil products or mixed hydraulic oils of different brands. After the new oil is replaced, let the engine idle for 15 minutes without rotating the mixing drum, and check whether the oil level is appropriate.

攪拌機新車購入養護需知說明就是這樣了，如果您的檢查或者保養工作不到位，很有可能會給設備造成一定的問題，注意事項的了解就來我們網站http://www.gdfcx.net咨詢吧。

This is the instructions for the purchase and maintenance of new blenders. If your inspection or maintenance work is not in place, it is likely to cause certain problems to the equipment. For the understanding of precautions, please come to our website http://www.gdfcx.net Consult.