如欲使攪拌機正常工作、延長使用壽命，就要遵守相關的各款原則以及操作準備，下面混凝土攪拌機廠家就來講講吧。

If you want to make the mixer work normally and prolong its service life, you must abide by the relevant principles and operation preparation. The concrete mixer manufacturer will talk about it below.

(1)在駕駛室內操縱操作手柄時，請勿踩踏加速踏板。

(1) Do not step on the accelerator pedal when operating the joystick in the cab.

(2)攪拌機行駛時，操作手柄應置于“攪動”檔內，駕駛室內的防逆手柄亦應加以鎖定。如操作手柄仍置于“進料、攪拌”檔內，則會降低預拌混凝土的質量，影響攪拌機的行駛性能。

(2) When the mixer is running, the operating handle should be placed in the "stirring" gear, and the anti reverse handle in the cab should also be locked. If the operating handle is still in the "feeding and mixing" position, the quality of ready mixed concrete will be reduced and the driving performance of the mixer will be affected.

(3)攪拌機開始工作前，發動機應空轉預熱。

(3) Before the mixer starts working, the engine shall be idled and preheated.

(4)扳動操作手柄時，切勿用力過猛。

(4) Do not pull the operating handle too hard.

行駛前的準備工作：

Safety preparation before driving:

車輛行駛前，應做好下列準備工作：

Before driving, the following preparations should be made:

(1) 將操作手柄扳“攪動”位置，使拌筒以攪動速度回轉。

(1) Turn the operating handle to the "stirring" position to rotate the mixing drum at the stirring speed.

(2) 將駕駛室內推拉軟軸操作手柄卡在定位塊的槽中鎖定。

(2) Lock the push-pull flexible shaft operating handle in the cab in the slot of the positioning block.

(3) 檢查卸料槽鎖柄是否扣牢。

(3) Check whether the lock handle of the discharge chute is fastened.

此外混凝土攪拌機出車前的作業檢查：

In addition, the operation inspection before the concrete mixer is set out:

檢查時如發現異?，F象，應找出原因并排除之。

If any abnormal phenomenon is found during inspection, find out the cause and eliminate it.

檢查部位：

Inspection position:

發動機起動前

Before starting the engine

減速機、柱塞泵潤滑油有無滲漏

Check whether the lubricating oil of reducer and plunger pump leaks

拌筒操縱裝置的操作手柄應置于空檔位置。

The operating handle of the mixing drum control device should be placed in the neutral position.

注意：如拌筒和發動機同時起動旋轉，則有可能發生危險。務必注意!

Note: if the mixing drum and the engine start and rotate at the same time, there may be danger. Be careful!

發動機預熱時

During engine warm-up

變量泵、馬達是否有異常

Whether the variable displacement pump and motor are abnormal

減 速 機是否有異常

Whether the reducer is abnormal

操作位置(發動機預熱后)拌筒的進料回轉和出料回轉是否正常,能否正常地進行回轉

Whether the feeding rotation and discharging rotation of the mixing drum at the operating position (after the engine is preheated) are normal and whether they can rotate normally

駕駛室內鎖緊桿是否鎖緊

Whether the locking lever in the cab is locked

大家要注意檢查時，切忌用手碰觸機器的轉動部分。并注意勿使衣服被機器卷入，是重要的，更多事項了解就來我們網站http://www.gdfcx.net看看吧。

Please note that during inspection, do not touch the rotating parts of the machine with your hands. And pay attention not to let the clothes be involved by the machine. Safety is important. Come to our website for more information http://www.gdfcx.net Take a look.